Search results for " power amplifier"
showing 10 items of 10 documents
High-Power Multicarrier Generation for RF Breakdown Testing
2017
Testing of satellite components for high RF power breakdown effects, such as multipactor and corona or passive-intermodulation, is a topic of growing interest in the aerospaceindustry. Switching fromthe classical single carrier approach to the more realisticmulticarrier scenario is very challenging from the experimental point of view. Themulticarrier signals, amplifiedby several RF power amplifiers, need to have controlled phase, amplitude, and frequency in each carrier. Fine tuning of the signal generator phases is required in order to compensate the phase drift occurring in the active elements of the test bed. This paper presents an efficient and low-cost technique to generate multicarrie…
Power efficiency improvements with the radio frequency H− ion source
2016
CW 13.56 MHz radio frequency-driven H(-) ion source is under development at the University of Jyväskylä for replacing an existing filament-driven ion source at the MCC30/15 cyclotron. Previously, production of 1 mA H(-) beam, which is the target intensity of the ion source, has been reported at 3 kW of RF power. The original ion source front plate with an adjustable electromagnet based filter field has been replaced with a new front plate with permanent magnet filter field. The new structure is more open and enables a higher flux of ro-vibrationally excited molecules towards the plasma electrode and provides a better control of the potential near the extraction due to a stronger separation …
A Battery-Free Smart Sensor Powered with RF Energy
2018
The development of Internet of Things (IoT) infrastructure and applications is stimulating advanced and innovative ideas and solutions, some of which are pushing the limits of state-of-the-art technology. The increasing demand for Wireless Sensor Network (WSN) that must be capable of collecting and sharing data wirelessly while often positioned in places hard to reach and service, motivates engineers to look for innovative energy harvesting and wireless power transfer solutions to implement battery-free sensor nodes. Due to the pervasiveness of RF (Radio Frequency) energy, RF harvesting that can reach out-of-sight places could be a key technology to wirelessly power IoT sensor devices, whic…
Cryogenic 35GHz pulse ENDOR probehead accommodating large sample sizes: Performance and applications.
2009
The construction and performance of a cryogenic 35GHz pulse electron nuclear double resonance (ENDOR) probehead for large samples is presented. The resonator is based on a rectangular TE(102) cavity in which the radio frequency (rf) B(2)-field is generated by a two turn saddle ENDOR coil crossing the resonator along the sample axis with minimal distance to the sample tube. An rf power efficiency factor is used to define the B(2)-field strength per square-root of the transmitted rf power over the frequency range 2-180MHz. The distributions of the microwave B(1)- and E(1)-field, and the rf B(2)-field are investigated by electromagnetic field calculations. All dielectrics, the sample tube, and…
Baseband predistorter using direct spline computation
2005
A baseband predistorter is presented. Key features of the predistorter reside in the use of cubic spline interpolation to generate predistorted input data to the power amplifier, without time convergence problems of classical approaches, with the goal of a reduction in the computational effort. Simulated behaviour of the proposed scheme is presented, demonstrating the effectiveness of the approach.
The effect of rf pulse pattern on bremsstrahlung and ion current time evolution of an ECRIS.
2010
Time-resolved helium ion production and bremsstrahlung emission from JYFL 14 GHz ECRIS is presented with different radio frequency pulse lengths. rf on times are varied from 5 to 50 ms and rf off times from 10 to 1000 ms between different measurement sets. It is observed that the plasma breakdown occurs a few milliseconds after launching the rf power into the plasma chamber, and in the beginning of the rf pulses a preglow transient is seen. During this transient the ion beam currents are increased by several factors compared to a steady state situation. By adjusting the rf pulse separation the maximum ion beam currents can be maintained during the so-called preglow regime while the amount o…
Design and analysis of filament power supply method for increasing life time of thermal emission tubes
2017
This paper has reviewed power supply methods for thermal electron tubes and proposes a method for purpose of increasing its lifetime, with reducing complexity of circuit and, improvement in power efficiency. In this work, the filament is operated with a decreased voltage level while maintaining the output anode power at the same level as required for the filament's operation at nominal voltage. The supply circuit is designed to avoid the reduction of filament voltage below a minimum level. A power converter made of thyristors and rectification diodes is designed to supply the filament voltage. Converter is carefully monitored and controlled by an algorithm embedded in a contemporary Digital…
Design of a High-Efficiency Ka-Band TWT Power Amplifier for Radar Applications
2022
The design of a high-efficiency Traveling Wave Tube (TWT) based on a non-conventional folded waveguide slow-wave structure (FW-SWS) operating over 34-36 GHz for naval and ground Ka-band radars is presented. The ridge vane-loaded FW structure allows a good compromise between high interaction impedance and wide bandwidth along with a low weight required for aircraft radar applications and a simple planar manufacturing process structure. Small signal simulations are performed with a custom interaction impedance evaluation program. The CST suite 2021 3D electromagnetic simulation code is used for the prediction of the dispersion diagram. Starting from a sensitivity analysis of the folded wavegu…
Collection, cooling and delivery of ISOL beams
1992
Abstract The collection of an ISOL beam in a Penning trap using implantation on a surface that is subsequently manipulated so as to become part of an end electrode of a Penning trap and reionization of the implanted material by heat has already been very productive for high-precision nuclear-mass measurements, even though it is limited to elements that are surface ionizable and the collection efficiencies are never better than about 0.1%. More recently, in 1990 a Paul trap system for electric collection of ions was installed at the ISOLDE-3 facility and collection was demonstrated for a 60 kV beam of 132 Xe ions. The purpose of this test setup was to determine the relationship between phase…
Robust single-parameter quantized charge pumping
2008
This paper investigates a scheme for quantized charge pumping based on single-parameter modulation. The device was realized in an AlGaAs-GaAs gated nanowire. We find a remarkable robustness of the quantized regime against variations in the driving signal, which increases with applied rf power. This feature together with its simple configuration makes this device a potential module for a scalable source of quantized current.